The presence of ions limits the charge extraction in perovskite solar cells, causing current losses. We used drift-diffusion simulation to validate this hypothesis and propose solutions to limit their influence – hence optimizing the power conversion efficiency (PCE).
Read the full post here: https://www.fluxim.com/mobile-ions-perovskite-solar-cells
Read MoreThe performance of light-emitting (LEDs) and photovoltaic (PV) devices depends on the quality of the photoactive semiconductor material. The unintentional introduction of defects in the semiconductor material due to material impurities or during the fabrication process causes the deviation from optimal performance.
These defects are referred to as trap states, or in short “traps”, which are energetic states within the bandgap of a semiconductor. In general, traps can occur due to material impurities (in the bulk) or at the interfaces between layers of different materials.
In the following blog post, we will present how to characterize the trap states with the technique called thermally stimulated current (TSC). We also propose a method to reliably interpret the TSC results based on drift-diffusion simulations.
Check the full tutorial here: https://www.fluxim.com/trap-states-perovskite-solar-cells
Read MoreHow do we perform aging experiments that are tailored to emerging PVs? This blog post summarizes the crucial guidelines that have been proposed by the community working on Perovskite Solar Cells (PSCs) to properly assess the stability of PSCs. These guidelines have been added to the existing indications provided by the ISOS protocols developed for Organic Solar Cells.
Read the full post here: https://www.fluxim.com/isos-protocols-stability-perovskite-solar-cells
Read MoreTransient photoluminescence (trPL) characterization experiments allow to analysis charge carrier dynamics and identify the recombination channels of the device structure under investigation.
Useful information that can be extracted includes the quantification of radiative and non-radiative lifetimes, charge carrier extraction from differential lifetime computation, and the influence of the interfaces on the recombination mechanism. Fitting the experimental results with simulations further supports the analysis of the obtained data. However, qualitatively comparable fittings can be obtained with different sets of simulation parameters.
Using the fully-coupled, 1-dimensional optoelectronic simulation software Setfos, the trPL signal of a simple glass/perovskite structure was simulated and a routine is suggested to ascertain the reliability of the results. This routine is based on experimentally measured material properties and the analysis of the band diagram evolution during the photoluminescence transient. The validity of the simulated trPL is also recursively verified by fitting the decay with a bi-exponential function to extract the lifetimes of the recombination mechanisms.
Check the full tutorial here: https://www.fluxim.com/transient-photoluminescence-perovskite-pvs
Read MoreThe open-circuit voltage (Voc) is the electrical potential difference between the two terminals of a solar cell, when there is no external load applied, hence no electric current flows. Correspondingly, this means that, when a voltage equivalent to the Voc is applied to the terminals of the solar cell, the recombination current (Jrec, which typically follows a non-ideal diode equation) and the photocurrent (Jph, the current generated by illuminating the solar cell) are equal, hence the net current is zero (Jrec=Jph at V= Voc).
Solar cells often present also non-radiative recombination mechanisms, in addition to the radiative one, as a result of poor material quality and non-idealities. To increase the Voc and thus potentially the power conversion efficiency, it is necessary to minimize the ΔVoc,nrad. It is, therefore, necessary to quantify the total loss and determine its origin.
Electroluminescence (EL) and photoluminescence quantum yield (PLQY) allow to directly extract the ΔVoc,nrad for thin-film solar cells such as perovskite solar cells, kesterite, perovskite, organic, or quantum dot. solar cells.
After quantifying the losses, the combination of capacitance-voltage (CV), temperature-dependent voltage characteristics (JV-T), and capacitance-frequency (Cf-T) measurements are essential to identify the recombination mechanisms.
Check the full tutorial here: https://www.fluxim.com/voc-losses-perovkiste-solar-cells
Read MoreA theoretical description of light emission, propagation, and re-absorption in semiconductor multilayer stacks is derived based on the transverse Green’s function of the electromagnetic field in the presence of a complex dielectric. The framework obtained is shown to reproduce the generalized Kirchhoff relations between the luminescent emission from metal halide perovskite slabs under uniform excitation and the slab absorptance of light with an arbitrary angle of incidence. Finally, consistent treatment of re-absorption provides the local rate of secondary photogeneration required for the consideration of photon recycling in an optoelectronic device simulator that includes the effects of charge transport.
Check the full tutorial here: https://www.fluxim.com/photon-recycling-in-perovskite-solar-cells
Read MoreOur 2D + 1D software LAOSS is a perfect tool to understand and improve on different upscaling strategies which combine 1D layer stack with 2D lateral simulations. In this blog post, we will discuss the findings by Matthias Diethelm and his colleagues who used LAOSS to simulate centimeter-sized organic solar cells to understand loss channels and macroscopic defects.
Read the full post here www.fluxim.com/electro-thermal-modeling-of-thin-film-solar-cells
Read MoreIn many perovskite solar cells, hysteresis is observed between the forward and reverse current-voltage (IV) scans. This IV curve hysteresis can be problematic for the correct determination of the Power Conversion Efficiency (PCE). While the exact origin of the IV curve hysteresis has remained a topic of debate, it is now widely accepted that mobile ions are the principal cause. However, it is still the subject of ongoing debates about how exactly mobile ions influence the device operation.
In this blog, we are showing how a proper drift-diffusion simulation can help in understanding how mobile ions are affecting the JV characteristics of a perovskite solar cell.
Read the full post here: https://www.fluxim.com/hysteresis-perovskite-solar-cells
Read MoreThe emerging solar cell technology of perovskite solar cells already reach an efficiency of 25.5%. The advantage of perovskite solar cells is that they absorb light better in the visible part of the spectrum whereas silicon-based solar cells can absorb near-infrared photons as well. This means that by combining these two technologies in tandem multi-junction solar cells, it will be possible to absorb light over a wide range of the spectrum very efficiently. Theoretically, efficiencies up to almost 40% are expected to be possible.
In this blog post, we will show how SETFOS can be used to analyze a tandem solar cell optically as well as electrically. This simulation approach reveals bottlenecks in the optimization and shows pathways for improvement. This study has been presented at the EUPVSEC 2020 by Urs Aeberhard.
Read the full post here: www.fluxim.com/perovskite-silicon-tandem-solar-cell-simulation
Read MoreWe present a numerical optimization of organic and hybrid multijunction solar cell devices , using an integrated optoelectronic device simulation approach that captures the essential properties of the complex multilayer structures, such as, light scattering at both macroscopic and rough thin film textures, resonator effects in coherent stacks, and the impact of organic interface properties for the design of efficient recombination layers . The optimization capabilities of the numerical device simulation framework are illustrated in the examples of textured perovskite silicon and all organic tandem solar cells.
Check the full analysis here: https://www.fluxim.com/simulation-multi-junction-solar-cells
Read MoreFLUXiM is a provider of device simulation software and characterization platforms to the display, lighting, photovoltaics and electronics industries worldwide.
